How to make drawers in a closet

The place in the closet is a very mysterious thing, sometimes it seems to us that it is enough, but when it comes to putting things in order in it, it turns out that a couple of drawers would not hurt. Most of such furniture is equipped with shelves, but drawers are better for ease of use. And if your cabinet does not have such, then they can be made by yourself.

Essential tools and materials for drawers

Drawers are very convenient to use, they are more practical than shelves, and it is easier to stack things in them. To make such shelves yourself, you will need the following tools:

  • high power screwdriver;
  • jigsaw for sawing materials;
  • roulette;
  • well-honed pencil;
  • building angle;
  • drills of sizes 5 and 8 mm;
  • rag;
  • knife.

Particleboard can be used as materials, but it is better to buy furniture wooden panels, there will be less waste from them. You can make a product from poplar, and the bottom of their birch plywood, its thickness is uniform, this material is quite durable.

DIY drawer assembly

Making drawers yourself is not at all difficult, but such work requires utmost precision, and a trained eye.

IMPORTANT! If you are not sure that you can cut the material as evenly and accurately as possible, it’s better not to take it - order a cut from a professional.

To start all the work, you need to determine the location of the future product. Be sure to measure the depth of the cabinet to know the dimensions of the corresponding fittings.

Selection and calculation of guides

To choose the right drawer, the width, height and depth of the drawer must be known, because the guides are one of the most important elements of the whole structure. There are two types of guides: roller and full roll. The second is more convenient to use. But if you decide to use roller retractable elements, be careful with their marking, it can cause difficulties, although the tolerances are the same for both types. You should not use wooden slats as a rollout, this is not practical, and it makes no sense to make a drawer, spend money on materials, and use wood at the same time. It is necessary to treat the process as professionally as possible in order for the result to please.

ATTENTION! The guides have a maximum length of 50 cm. If the depth of the drawer is the same, then for guides that are tight, get guides of 45 cm.

Marking the position of the guides is a responsible matter, although not complicated. It is important to be careful. The main thing is to start making all measurements from above. When marking, half the height of the upper facade is taken into account. You will need to attach the guides to the marking line.

Measure the opening where the box will be installed and its height. The width of the finished product must be reduced by 25 mm, because the width of the guides is 12.7 mm.

Box Detailing

For the manufacture of boxes it is better to buy furniture panels, you can use chipboard, but this is not economical, since you will get a lot of leftovers. If you are a very good carpenter, and have experience working with wood, then it will not be difficult to prepare all parts of the future product, but not all are craftsmen. That is why it is better to order a cut in the workshop, or use such services in the place where the material was purchased. Do not forget that you will need the following blanks:

  • facades;
  • side parts;
  • the walls of the boxes are front and rear.

If, nevertheless, you decide to make a cut yourself, then the length of all the parts is best marked with an emphasis, not a tape measure. Any box has a bottom, so you need to cut it. For these purposes, a hardboard is suitable, the details are screwed to the finished product.

Fasteners and fittings

To assemble the product, you need a standard mounting kit:

  • confirmations;
  • self-tapping screws of different lengths.

Manufacturing process

Before assembling the boxes, all parts must be processed. Glue the edge along the edge. You need to attach an edge to the end, turn on the iron for almost all power, and apply it to the edge. Such actions must be repeated several times, then go along the edge with a dry rag, smoothing the edges. If there is an extra edge, cut it off with a knife, but very carefully so as not to spoil it. To prevent burrs on the workpiece, sand it using sandpaper.

For fasteners, holes 8 mm in diameter must be made. The hole in the end will be 5 mm. Further, guides are attached, they, as a rule, pass in the middle of the box.

Retractable full roll-out elements are sold in pairs, they must be disconnected before installation. If you make drawers for the cabinet, then you need to fasten the guides on the inside of the cabinet, and on the outside of the box. Do not forget to retreat 3 mm from the edge of the inner wall of the cabinet when fastening the rails.

To install these elements exactly, you need to follow simple rules:

  1. Drill a small hole in the facade to install the handles.
  2. Attach the drawers and fasten from the back through the drilled holes. Next, you need to pull out the drawer, and in the normal position fix the guides inside. After all these steps, the fasteners must be unscrewed.
  3. Now you need to drill holes so that you can install the handle.

In this simple way, you can make drawers yourself. If you do all the work correctly, then the design will work correctly, and this is important. If, nevertheless, somewhere you see flaws, or incorrect operation of the product, check your calculations again, a mistake may have been made. In this case, everything will have to be fixed.

IMPORTANT! For all calculations, you need to be very careful so that the final result can please the first time.

Try it, and you will succeed. After all, it is always better to make something yourself than to look for a similar product in a store.

Watch the video: How To Make Drawers Fast And Easy (March 2024).

Leave Your Comment